Dana 35 gear oil capacity.

Make sure the GL-5 gear lube you use is a conventional, not a synthetic. Your new gears need to be kept cool and they'll run cooler when lubricated with a conventional gear lube. The exact viscosity is not critical. 75W-90, 80w-90, etc. is fine.1999 to 2016 Super Duty - Dana 50 front axle oil capacity? - So, I read my manual and it says that the dana 50 front axle on my 2000 should take 1.8l (3.8 pints) of oil. I drop the cover and drain it, pour back in 2 quarts of lube and it is nowhere near the fill hole, I cant even reach the oil with my little finger up...The fluid looked good, as did the gearing and locker.) I replaced the chrome cover that was previously installed with a Rugged Ridge cover. From what I have found, the Dana 44 should take 3.6 pints of gear oil. Does that sound about right for what is supposed to be a 1971 Dana 44?Next go to the trans filler port on the left and top it off... After you drive a few miles, recheck and top off the trans again. Why? #1 The trans filler port is higher than the transfer case filler. #2 The trans and transfer case share oil. #3 Topping off at the trans filler port will raise the oil level in the TC.

Oil for differentials Dana 30/35 Jump to Latest Follow 10K views 7 replies 6 participants last post by josef15111 Mar 11, 2010how much gear oil for dana 60? Thread starter 73dodge; Start date Sep 24, 2007 - 7. 73dodge Well-Known Member. Joined Sep 12, 2007 Messages 65 Reaction score 0. Sep ...50629 posts · Joined 2005. #3 · May 7, 2015 (Edited) Nearly any major brand GL-5 gear lube is fine. Valvoline, Castrol, Torco, Havoline, etc. will be good. A 75W-90 is good around town, a heavier viscosity like 80W-120 or 85W-140 is good if you tow a trailer or wheel extreme trails. Ever since custom axle builders like Currie discovered ring ...

rootster. 1467 posts · Joined 2004. #3 · Aug 23, 2007. KOPY KAT said: I've searched the threads, but can't find a satisfactory answer: I have an '03 TJ Sport with dana 30 /35 diffs. I want to change the oil, but the rear 35 has a tag that says "use limited slip additive"--and the build sheet confirms it as a Dana 35 Limited Slip diff.

4332 posts · Joined 2008. #1 · Jul 26, 2011. Just checked the FAQ and it said to use 75w140 on the rear dana 35 and 80w90 on the front dana 30. Can I use 80w90 on the rear or is it a bad thing. Im open/open on the axles too. Thanks.dana 44 rear diff fluid amount. diff fluid differential fluid level. Jump to Latest Follow. 27K views 29 replies 6 participants last post by DoubleOught Mar 25, 2014. dirtbag90 Discussion starter. 96 posts · Joined 2014. #1 · Mar 21, 2014. My rear dana 44 was only able to take about 1 and 3/4 qt. I know manual says 2 qts or 4 pints.4.0L Engine Oil: 6 Quarts / 5.7 Liters: 10w-30 or 5w-30: 4.2L Engine Oil: 2.5L Engine Oil: 4 Quarts / 3.8 Liters: 4.0L Coolant: 10.5 Quarts / 9.9 Liters: 50/50 Mixture of Antifreeze and water: 4.2L Coolant: 2.5L Coolant: 9.0 Quarts / 8.5 Liters: NV231 Transfer Case (Man Trans) 1.6 Quarts / 1.5 Liters: ATF 3 or ATF 4: NV 231 Transfer Case (Auto ...- Gear oil - 80 weight for light duty and normally cooler climates - 90w120 weight for heavy duty and normally warmer climates Note: Some rear axles are equiped with factory posi - a limited slip additive must be put in with the gear oil to extend and protect the limited slip action Dana 30 = 2.5 pints Dana 35 = 3.5 pints Dana 44 = 4.0 pints ...

It is a heavy-duty, gear-driven transfer case with a 23-spline input shaft. The case is cast iron but the tail housing is aluminum. The ID number C300-15 is stamped on the case. The output for the front drive shaft is on the right side and the rear output in line with the input. Low range is 2.62:1.

The gearing used in today's Dana 44™ axles has a 226 mm ring gear size and has a torque capacity of 8200Nm. The new generation Dana 44™ AdvanTEK ® gearing has a smaller 220mm ring gear size but has the same torque capacity of 8200Nm. These high-performance axles are a prime example of Dana’s efforts to address: Efficiency; Power density

The oil capacity is about 3 quarts, Dana recommends 80w90 gear oil ... The ring gear diameter is 10.5" The 35 spline versions are the same spline as the 35 spline 60 ...Received 475 Likes on 422 Posts. NCM Sinkhole Donor. For gear oil, you can use a good grade of GL-5 rated 80W-90 (Valvoline is fine) and a bottle of the GM posi additive. Shouldn't take more than 2 quarts. For the driven gear, go to a reputable tranny shop or try the dealer. Just tell them you have 3.45 gears and you need the gear for a …When it comes to maintaining your motorcycle’s performance and ensuring a smooth ride, checking the fork oil capacity is an essential task. The fork oil not only lubricates the sus...mrmoparwl. 339 posts · Joined 2009. #9 · Aug 3, 2010. The problem with only one bottle is the increased amount of fluid the Dana 70 and 80s have over the 60. Seen enough of the 70s eat up the clutches by not adding enough slip lube. When I service any 70 or 80 min amount is 1 1/2 bottles in the 70 and 2 in the 80.Fortune Favors the Brave. Feb 8, 2011. #2. oil weight must be hypoidal gear oil. 80w-90. my 7.5" diferential uses 2.5 quarts of oil. im not sure how much yours will need tho.Feb 24, 2002. Messages. 10,875. Oct 6, 2003. #2. My 74 manual said to use non deturgent 50 weight motor oil. I use synthetic 90 weight gear oil it is lighter than 50 weight motor oil and gives the protection of 90 weight. It is uneffected by water if you should go so deep. It also makes shifting the transfer case slightly easier.79 Bronco 460/auto 35" Swampers 93 Lightning with KB 2.2 ... *Front differential Oil Capacity 5.9pt ... -Dana S135 24.5 pt-Ford 10.50-Inch Ring Gear 7.0 pt-Friction Modifer 8.0 oz *Rear Differential Fluid Type *Ford 10.50 Inch Ring Gear -SAE 75W140 High Proformance Rear Axle Lubricant-Additive Friction Modifier C8AZ-19B546 …

May 8, 2017 · In other words, 85W-90, 80W-90, 80W-120, 85W-140, etc. are all fine viscosities depending on how you drive it. For milder uses and colder climates, a lower viscosity is fine. For rougher uses including towing, stick with a higher number viscosity. The exact viscosity of gear lube is not all critical, just make sure whatever gear lube viscosity ... May 15, 2014 · I have always liked Mobil synthetic products. However, for our 1999 Jeep XJ Cherokee Dana 30 and Chrysler 8.25" axles with ARB Lockers, I use Mopar 75W-120 synthetic gear lube. I use this same lube in the 9.25" and 11.5" AAM axles in the 2005 Ram 3500 4WD truck. Received 2 Likes on 2 Posts. Usually add 2 bottles of the Ford LSD additive to a large differential like a 70. You can use 75W-90, 80W-90, 85W-140. Just about anything specified as gear oil. With something like a motorhome that sees extended periods of high speeds at a heavier weight, you might think about using the higher viscosity oil.The extended drain program and any extended warranty program are separate programs. Note: For specifi c detail on Dana extended warranty programs refer to the Dana Warranty Guide or call 1-877-777-5360. Note: For a complete list of Dana “approved lubricants” for extended drain, refer to Approved Lubricant Suppliers Manual, DALSM072012.It had auto trans fluid in it. I didn't think it was unusual because the suburban runs with that. What I learned from all the helpful folks is the D 300 is a gear driven design and uses gear oil (85w90).Suburban is chain driven and uses dextron. I just use the 80w90 from walmart. (Checking every other week cause it leaks out)

7005 posts · Joined 2008. #2 · Jul 8, 2012. Typically after replacing the ring and pinion gear, you'll want to run 80w-90, but the most important thing is to run a conventional oil during break in. Synthetic gear oil is great at preventing wear, but the new gears need a chance to wear into each other. As long as you're running a conventional ...I put in exactly recommend amount of 1.75 quarts. That amount barely fill up the bigger cover. Some recommend adding till fluid comes out of the filling hole. I just can't imagine added that much fluid. Has anyone who have bigger covers like Solid differential have the same problems? And how much gear oil did you fill?

Always fill to the proper level regardless of capacity listed. I really can't help with questions about the M200, other than its a Dana 35. Knowing what I know about lubricants for industrial gear drives, I can only assume that the M200 sees higher loads than the M220, requiring a lubricant with a higher viscosity at operating temperature.The extended drain program and any extended warranty program are separate programs. Note: For specifi c detail on Dana extended warranty programs refer to the Dana Warranty Guide or call 1-877-777-5360. Note: For a complete list of Dana “approved lubricants” for extended drain, refer to Approved Lubricant Suppliers Manual, DALSM072012.4332 posts · Joined 2008. #1 · Jul 26, 2011. Just checked the FAQ and it said to use 75w140 on the rear dana 35 and 80w90 on the front dana 30. Can I use 80w90 …spillz Discussion starter. 160 posts · Joined 2007. #11 · Jan 3, 2014. Called ARB. Hi everyone, I called ARB tech department with my concerns as to the correct amount of fluid for my differentials. ARB Tech. stated that they would require the factory amount in each diff, which is 2.5 pints in Dana 30 and 4.0 pints for the Dana 44.What happens to a truck if it tows more than its capacity? You don't want to know. Learn more about what happens if a truck tows more than its capacity here. Advertisement Temptati...What type of oil should I use in an early Bronco Dana 20 transfer case? For the 66-77 Ford Bronco Dana 20 transfer case we recommend standard 80/90 weight gear oil. How much oil does the early Bronco Dana 20 transfer case use? The Dana 20 transfer case oil capacity is 1.375 quarts. Fits 66-72 Ford Bronco.Another first for me! Changing the rear differential fluid on the YJ. For this project on the Jeep I used a gasket I found on amazon and 80w-90 oil. Whoever ...

I have a factory Dana 44. I was wondering how oil it takes? Some say to fill it until it comes out the fill hole. When I went to 6" coils from 4" coils it changes the angle of the pumkin and decreases the amount of oil it can hold. I can only imagine how much less it was able to hold going factory height to 6" lift. A buddy told to put in 1.5 ...

7005 posts · Joined 2008. #2 · Jul 8, 2012. Typically after replacing the ring and pinion gear, you'll want to run 80w-90, but the most important thing is to run a conventional oil during break in. Synthetic gear oil is great at preventing wear, but the new gears need a chance to wear into each other. As long as you're running a conventional ...

If your car doesn't move when you put it into gear, it may be due to a simple oversight or you may have a serious transmission problem. The source of the probelm may depend on whet...The official fill capacity of the Dana 35 is 3.5 pts. or 1.75 quarts. Even with a slight volume different due to a custom cover I would just pour in 1 3/4 quarts, maybe an RCH more for a larger capacity cover, and call it a day.It depends on where you live and how you drive. In a hot place with no winter weather, you want a thicker oil, say a viscosity over 90. If a cold place then want a lighter oil below 90. If a lot of heavy and hot towing, then a heavier oil. It is just like motor oil. Hotter, go heavier. Colder, go lighter.Dana 28: Dana 35: Ring Gear Diameter: 6.625 Inches: 7.56 Inches: Ring Gear Bolts (8) 3/8″ x 24 RH: Pinion Stem: 1.312 Inch: ... The above photo shows a Dana 35 hybrid on the left that houses the Dana 28 carrier/gears. ... Galpin 1966 Ford Bronco In Gulf Oil Livery September 3, 2023; 1969 Ford Bronco Twin Turbo Ecoboost August 3, ...As others suggested, 2 quarts butnyoull use only around 1.3 quarts. I suggest jacking the axle up to get more fluid in there. At ground, the hole will be lower and less fluid. This will be your friend.I checked the Dana website and the info they have is to use a minimum of S.A. E. 80W/90 multi purpose gear lube. They recommend to use the specified lubricant that the vehicle manufacturer recommends. Thanks in advance. Don. 2003 7.3 PSD 2wd XLT super cab long box, drw, automatic trans. 410 gears, stock exhaust with muffler delete, PHP chip ...Dana 30 = 2.5 pints. Dana 35 = 3.5 pints. Dana 44 = 4.0 pints. *Engines: - 10w30 for good general usage in most climates. - 5w30 for those colder climates (when …Dana 30 = 2.5 pints. Dana 35 = 3.5 pints. Dana 44 = 4.0 pints. *Engines: - 10w30 for good general usage in most climates. - 5w30 for those colder climates (when … Capacity: Dana M190: 2019-2020: Motorcraft SAE 80W-90 Premium Rear Axle Lubricant: 1.64-pints (0.775 Liters) Dana 35 SLA: 2001-1998: Motorcraft SAE 80W-90 Premium Rear Axle Lubricant: Front axle L (pint) 1.54 (3.25) / Lubricant level mm (in) 9.56 (0.38) below bottom of axle cover filler hole: Dana 35 TTB: 1990-1997: Hypoid Gear Lubicant SAE 80W ... What is gear oil weight? A gear oil’s weight, or viscosity, is measured like engine oil by its thickness with a numerical value associated with it—albeit much thicker. Where engine oil may be in the 10W30 range for a multi-weight oil, gear oil is more often in the 75W90 range. Like engine oils, the first number shows the oil’s thickness ...

I replaced the OEM oil with Amsoil Severe Gear--75W-110 in the front and 75W-140 in the rear. It took 1.3QTs in the front and 1.6QTs in the rear. Off-Roading in my Wildtrak; taking a break from Wranglerville.- Gear oil - 80 weight for light duty and normally cooler climates - 90w120 weight for heavy duty and normally warmer climates Note: Some rear axles are equiped with factory posi - a limited slip additive must be put in with the gear oil to extend and protect the limited slip action Dana 30 = 2.5 pints Dana 35 = 3.5 pints Dana 44 = 4.0 pints ...dana 44 rear diff fluid amount. diff fluid differential fluid level. Jump to Latest Follow. 27K views 29 replies 6 participants last post by DoubleOught Mar 25, 2014. dirtbag90 Discussion starter. 96 posts · Joined 2014. #1 · Mar 21, 2014. My rear dana 44 was only able to take about 1 and 3/4 qt. I know manual says 2 qts or 4 pints.Instagram:https://instagram. countryhuman makercheck engine light on a chevy cruzejohn elliott cbs ageanvy nails union 17,625. Location. taxifornia,soon 2b Arizona. I had a good friend (passed away now from cancer) who made his living as a one man rearend shop. His specialty was nine inch ford for racers, but he could work on anything. If the customer insisted on synthetic gear oil, he would warrantee his work for six seconds/six inches, whichever came first.The fluid looked good, as did the gearing and locker.) I replaced the chrome cover that was previously installed with a Rugged Ridge cover. From what I have found, the Dana 44 should take 3.6 pints of gear oil. Does that sound about right for what is supposed to be a 1971 Dana 44? toledo rv show 2024mini bernedoodle haircut That's the Gear Lube Spec. As for the gasket www.4wd.com or www.quadratec.com and several dozen others. If you are in a hurry you can walk into any transmission shop that does 4wd and get one the next day (in … old national bank columbus Mar 21, 2014 · dana 44 rear diff fluid amount. diff fluid differential fluid level. Jump to Latest Follow. 27K views 29 replies 6 participants last post by DoubleOught Mar 25, 2014. dirtbag90 Discussion starter. 96 posts · Joined 2014. #1 · Mar 21, 2014. My rear dana 44 was only able to take about 1 and 3/4 qt. I know manual says 2 qts or 4 pints. Capacity 12 - 12,000 lbs. 18 - 18,000 lbs. 22 - 22,000 lbs. 24 - 24,000 lbs. Series Beam Type F = I-Beam Standard Overall Width T = Tubular Beam Beam Drop 1 - 1.5 in. to Tube Centerline 4 - 3.5 in. to Spring Pad 5 - 5.1 in. to Tube Centerline EFA 12 F 4 I 120 SG Nominal Load Carrying Capacity 60 = 6,000 lbs. 80 = 8,000 lbs. 100 = 10,000 lbs ...